Dark Raw Tung Oil
|Availability:||In stock (1)|
INSTANTLY ADD DEPTH TO YOUR GRAIN FOR AN AGED-ANTIQUE FINISH
The same as our Pure Tung Oil except that we have added a non-toxic naturally occurring resinous hydrocarbon for color. The resin is non-carcinogenic and does not contain any PCB’s. Dark Raw Tung Oil by The Real Milk Paint Company is water and alkali resistant. It resists marring, penetrates well, elastic and unlikely to check. Dark Raw Tung Oil builds quickly, consolidates the wood surface and builds a dark matte wood finish. It should be kept in an airtight container with minimum air space.
- Naturally polymerizing wood finish
- Cures by oxidation not evaporation
- Does not form a glossy finish no matter the number of coats
- Form a flexible water proof finish
- Resists abrasion and acids
- Does not blister and peel (properly applied)
- Does not mold like linseed oil
- Long shelf life
- Does not darken with time like linseed oil
- Concentrated (thin one to one, doubles the coverage)
- Combined with “Citrus Solvent” makes an all-natural wood finish
- FDA approved for food contact
- Does not go rancid
- 7 to 10 days partial cure, 15 to 30 days full cure
- Can be mixed with any other of our Tung Oil Products (i.e. Pure Tung Oil, Dark Half, Half & Half, Outdoor Defense Oil)
- 8 oz. covers 25 sq. feet
- 16 oz. covers 50 sq. feet
- 32 oz. covers 100 sq. feet
- Gallon covers 400 sq. feet
This is coverage for the oil only and not diluted with Citrus Solvent.
DIRECTIONS FOR USE
- The surface should be dusted to remove all loose particles.
- Any wood filling or wood staining (water or alcohol stains work best) must be done before the oil is applied.
- Using the Dark Tung Oil straight from the bottle would only be for the most thirsty surfaces like old weathered wood, 100 year old wood floors that were never finished or concrete.
- We recommend thinning Dark Tung Oil with either natural Citrus Solvent.
- The first coat of thinned tung oil should be a liberal one.
- Apply with a natural bristle brush, sponge brush, or a thin foam roller.
- Allow this coat to sit for a minimum of 40 minutes so the oil can soak in. When it soaks into the wood, apply another coat immediately. Continue to apply coats, one after another, until the wood/concrete is saturated and stays glossy for a minimum of 40 minutes up to 1½ hours. If eighty percent of area stays glossy, the wood cells are saturated and this can be considered your final coat.
- Now, wipe down the surface with clean rag material removing any excess oil that is on the surface. Continue to check for any seeping in the next few hours, and rub this off as well. Do not allow standing oil on the surface overnight. Any standing or puddles of oil should be wiped away with clean rags.
- After allowing the oil to soak overnight, apply one more coat to the surface the next day. Let this sit for a minimum of 40 minutes, but no more than 2 hours. Wipe up any oil that has not soaked in. Now the tung oil will be in its curing stage.
- Hang oil soaked rags up separately to dry. For woods with very dense pores like Teak wood, thin with two parts Citrus Solvent to one part oil will help it absorb better for every coat.
- Dark Half will take 7 to 10 days for a minimum cure and 15 to 30 days for a full cure.
- Do not sand between coats of tung oil. This is an application technique for tung oil varnishes, not pure tung oil.
- Tung oil can be applied pure to very porous surfaces. We recommend thinning of the Dark Tung Oil with either natural Citrus Solvent or Odorless Mineral Spirits. Check out our Dark Half, a pre-thinned, non-toxic Dark Tung Oil mix with Pine Oil.
- Do not use the “Green” thinners now being sold. They contain water and will not mix with the oil.
- Remember by adding petroleum mineral spirits or other thinners, the oil may become toxic with these substances mixed into it, although the finish produced is not toxic because the thinners evaporate.
- The number of coats of oil to be applied will be determined by the intended use of the piece. One to two coats are enough for decorative work, paneling and molding. For surfaces that receive moderate to heavy use or handling need a minimum of three and on up to six coats for maximum protection.
- Apply till the surface reaches the saturation point. This will be evident as the surface will not absorb more oil.
- Renewal and/or maintenance coats are thinly applied with cheese cloth, lint free cloths (old bed sheets work well), or old t-shirt material on an as need be basis. A two parts solvent to one part tung oil mixture is recommended for maintenance coats.
- Do not get hung up on the number of coats, let the wood tell you when it has reached its maximum saturation.
- The Pure Tung Oil contained in Half & Half will be in the wood up to the surface not on the wood surface like varnish or Polyurethane top coat. The end result is more like seasoning a cast iron pan. This product will give you a surface that will stand up to vigorous use and spills: water will bead on the surface.
- After the tung oil as completely cured (minimum 30 days) cleaning of the surface can be done using hot water and mild soap, such as dish soap. Avoid using hard chemicals or acids for cleaning.
- 8oz covers 25sq. feet
- 16oz covers 50sq. feet
- 32oz covers 100sq. feet
- Gallon covers 400sq. feet
- Example: One Gallon would cover 400sq. feet one time.
Pure Tung Oil is a finishing product that provides a tough, flexible and highly water-resistant coating for a great wood finish when staining wood. It is classed as a drying oil along with linseed, poppy seed, safflower seed, walnut, soybean, oiticica and a few other oils. Although it is relatively new to the Western world, tung oil has been known for centuries to the Chinese, and until this century, China was the main source for the oil. It comes from the seed of the tung trees, Aleurites fordii and Aleurites montana, deciduous trees that are very susceptible to frost damage. This vulnerability has restricted the cultivation of the tung trees to China and South America. Tung oil received wide application in China: in the building trades as a treatment for both stone and wooden structures; in marine trades as a preservative and water repellant on wooden boats.
It is said to have been introduced to the West by Marco Polo. From the 13th to the 19th century, tung oil had only limited use in the West. In the 19th century it was adopted by the paint companies to become a major component in paints and varnishes. More recently, tung oil has gained favor over linseed oil for furniture finishing because it is faster drying and does not darken as much with age.